SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Solutions
Supports APSD for optimal VoIP applications
Patented spurious noise cancellation algorithm for integration in SOC applications
Supports Bluetooth co-existence interface
Self-calibrated RF to ensure optimal performance under all operating conditions
Zero factory tuning
No external RF components
Specifications
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
Microcontroller:ATmega32u4
Operating Voltage:5V
Input Voltage (recommended):7-12V
Input Voltage (limits):6-20V
Digital I/O Pins:20
PWM Channels:7
Analog Input Channels:12
DC Current per I/O Pin:40 mA
DC Current for 3.3V Pin:50 mA
Flash Memory:32 KB (ATmega32u4) of which 4 KB used by bootloader
SRAM:2.5 KB (ATmega32u4)
EEPROM:1 KB (ATmega32u4)
Clock Speed:16 MHz
Length: 68.6 mm
Width: 53.3 mm
Weight: about 20g
ATmega168 running at 16MHz with external resonator
USB connection off board
Supports auto-reset
Max 150mA output
Over current protected
Reverse polarity protected
DC input 5V up to 12V
On board Power and Status LEDs
Size：（Long）33mm *（wide1）18 mm *（high）6mm
Package Content
1PCS Arduino pro min atmega168p board
3PCS Gilded Pin
1. Size:37mmx25cmx32mm/1.45''x0.98''x1.26''
2. Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. This joystick module can be easily connect to Arduino by normal IO Expansion Shield with supplied cables.
01. The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
02. Power your developement in the fastest way combinating with NodeMCU Firmware!
03. USB-TTL included, plug&play
04. 10 GPIO, every GPIO can be PWM, I2C, 1-wire
05. FCC CERTIFIED WI-FI module(Coming soon)
06. PCB antenna
1 single module can drive the an 8 * 8 dot matrix common cathode
2 the module Operating voltage: 5 v
The Module 3 dimensions: length 3.2 cm X 3.2 cm wide X 1.3 cm high
4 holes with four screws, the diameter of 3 mm
CPU: Broadcom BCM2835, which can run at up to 1GHz.
RAM: 512MB
Power: 5V, supplied via micro USB connector, drawing 160mA (even when connected to an HD display).
Dimensions: 65mm x 30mm x 5mm
Video & Audio: 1080P HD video output. Audio output via mini-HDMI connector.
Storage: MicroSD card.
Operating System: Linux, installed via NOOBS.
This module is only USB serial port module, is responsible for converting the USB interface into the ESP8266 module serial port. WiFi knowledge of all aspects of the query module ESP8266 related information!!
