GSM 850/900/1800/1900MHz GPRS Class 12
TCP/ IP build in GSM Module GPS Module SIRF Star III GPS Channels
20 Tracking sensitivity -159dBm Acquisition sensitivity
144dBm Locating time cost Hot start:<2sec(open sky);warm start:<15sec;cold start:
GT02A is a Mini intelligent GPS Vehicle positioning terminal. It combines the GSM wireless communication technology and GPS positioning system technology,terminals using industrial-grade highly integrated design,intelligent power-saving and passive drift suppression,installation is simple,connect the power supply to start work immediately,wide inpute voltage range,wide applicable to all types of cars,motor cycles,electric cars,ships,etc., can provide all-weather,real-time vehicle positioning function,with global positioning service platform,you can achieve remote vehicle management.
Specifications
Bluetooth Protocol: Bluetooth Specification V4.0 BLE
USB Protocol: USB V2.0
Operating Frequency: 2.4GHz ISM band
Modulation Mode: GFSK (Gaussian Frequency Shift Keying)
Transmitting Power: =4dBm
Sensitivity: =-84dBm at 0.1% BER
Transmission Rate: 6 kbps (asynchronous & synchronous)
Security Feature: Authentication and encryption
Audio Input: Wireless Bluetooth
Max. Receiving Distance: 10 Meter
Power Output: Dual-channel 15 W+15 W
Applicable Speaker Impedance: 4/6/8/10 ohm
Supply Voltage: DC 10~25 V(recommended DC 12V More than 2A)
Specification
1.Works with standard (dual 5/3.3V) and 3.3V-only (for example, Arduino Pro)boards.
2.Operates over the extended -40°C to +85°C temperature range
3.Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral,
4.Full-/Low-Speed 12Mbps/1.5Mbps Host)
Features:
1. Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.
2. 125 Channels, Multi-point communication and frequency hopping to meet the communication needs
3. Built-in hardware CRC error detection, Multipoint communication address control.
4. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
5. Built-in 2.4Ghz antenna
6. Available software to set the address, only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
7. Built-in voltage regulator
8. Standard DIP Pitch Interface for embedded applications
9. size: 34mm X 17mm X 1mm
Package Included:
1 xArduino NRF24L01+ 2.4GHz Wireless Transceiver Module
Parameters:
PCB Dimensions: 26.5* 15.6mm
With 3.3V and 5V dual power output
With three LEDs: power indicator, data reception indicator, the data transmission indicator, working status
With self-recovery fuse. In the event of accidental short circuit, it can effectively protect your computer USB port and Downloader
With reset signal output, etc. directly to the for Arduino board Promini download!
Features:
* 802.11 b / g / n
* Wi-Fi Direct (P2P), soft-AP
* Built-in TCP / IP protocol stack
* Built-in TR switch, balun, LNA, power amplifier and matching network
* Built-in PLL, voltage regulator and power management components
* 802.11b mode + 19.5dBm output power
* Built-in temperature sensor
* Support antenna diversity
* off leakage current is less than 10uA
primary info
penetrating ability SI4432 IC, stable performance
Frequency Range: 433.92M
Sensitivity up to-121dBm
Maximum output power: 20dBm
Data transfer rate :0.123-256kbps
FSK, GFSK and OOK modulation mode
1.8-3.6 V power supply
Low consumption shutdown mode
Digital received signal strength indicator (RSSI)
Timing wake-up function
The antenna automatically match and two-way switch control