The HC-05 bluetooth module can be set as a transmitter or receiver. You can combine this bluetooth module with your system: MCU, ARM or DSP systems, SOC systems.
This module can build a connection to other modules in two ways: as a master or as a slave. Ex, a robot can be designed to be a master connected to a slave bluetooth module or as a slave board to make a wireless connection with a PC.
Integrated Bluetooth Serial Pass-through Module Master-Slave 6 Pin JY-MCU anti-reverse
Brand new, factory sealed, never open
High frequency: 2.4GHz
With VCC, GND, TXD, RXD, EN, STATE foot for the Bluetooth
Master and slave, Two modes in one module
Use the CSR mainstream bluetooth chip
Bluetooth V2.0 protocol standards
Input voltage: 3.6~6V; Prohibit more than 7V
Fully compatible with Arduino
High speed: Asynchronous: 2.1Mbps(Max) / 160 kbps, Synchronous: 1Mbps/1Mbps
Incredible small size (about the size of a dime ), and RoHS Compliant
TTL data transparent
Transfer between a host Bluetooth device
Item Weight: 0.2 ounces
Works for Bluetooth TTL transceiver module which allows your target device to both send or receive the TTL data.
Coverage up to 30ft. Built in antenna.
Working current: matching for 30 mA, matching the communication for 8 mA
Used for GPS navigation system, water and electricity gas meter reading system
With computer and bluetooth, bluetooth adapter, PDA, seamless connection equipment .
Features:
1. Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.
2. 125 Channels, Multi-point communication and frequency hopping to meet the communication needs
3. Built-in hardware CRC error detection, Multipoint communication address control.
4. Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
5. Built-in 2.4Ghz antenna
6. Available software to set the address, only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
7. Built-in voltage regulator
8. Standard DIP Pitch Interface for embedded applications
9. size: 34mm X 17mm X 1mm
Package Included:
1 xArduino NRF24L01+ 2.4GHz Wireless Transceiver Module
Module stereo output, built-in Bluetooth antenna structure is simple, the power supply voltage is 3.7V~5V version selection, active speakers increase Bluetooth connection function. 7PIN output interface is spacing 2.54 through hole, 7PIN output interface is: + power, ground, left channel, right channel, mute, LED status indicator, reserved port.
primary info
penetrating ability SI4432 IC, stable performance
Frequency Range: 433.92M
Sensitivity up to-121dBm
Maximum output power: 20dBm
Data transfer rate :0.123-256kbps
FSK, GFSK and OOK modulation mode
1.8-3.6 V power supply
Low consumption shutdown mode
Digital received signal strength indicator (RSSI)
Timing wake-up function
The antenna automatically match and two-way switch control
Specifications
Bluetooth Protocol: Bluetooth Specification V4.0 BLE
USB Protocol: USB V2.0
Operating Frequency: 2.4GHz ISM band
Modulation Mode: GFSK (Gaussian Frequency Shift Keying)
Transmitting Power: =4dBm
Sensitivity: =-84dBm at 0.1% BER
Transmission Rate: 6 kbps (asynchronous & synchronous)
Security Feature: Authentication and encryption
Specification
1.Works with standard (dual 5/3.3V) and 3.3V-only (for example, Arduino Pro)boards.
2.Operates over the extended -40°C to +85°C temperature range
3.Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral,
4.Full-/Low-Speed 12Mbps/1.5Mbps Host)
