ATmega168 running at 16MHz with external resonator
USB connection off board
Supports auto-reset
Max 150mA output
Over current protected
Reverse polarity protected
DC input 5V up to 12V
On board Power and Status LEDs
Size：（Long）33mm *（wide1）18 mm *（high）6mm
Package Content
1PCS Arduino pro min atmega168p board
3PCS Gilded Pin
I am text block. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Solutions
Supports APSD for optimal VoIP applications
Patented spurious noise cancellation algorithm for integration in SOC applications
Supports Bluetooth co-existence interface
Self-calibrated RF to ensure optimal performance under all operating conditions
Zero factory tuning
No external RF components
Specifications
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
Microcontroller:ATmega32u4
Operating Voltage:5V
Input Voltage (recommended):7-12V
Input Voltage (limits):6-20V
Digital I/O Pins:20
PWM Channels:7
Analog Input Channels:12
DC Current per I/O Pin:40 mA
DC Current for 3.3V Pin:50 mA
Flash Memory:32 KB (ATmega32u4) of which 4 KB used by bootloader
SRAM:2.5 KB (ATmega32u4)
EEPROM:1 KB (ATmega32u4)
Clock Speed:16 MHz
Length: 68.6 mm
Width: 53.3 mm
Weight: about 20g
The Mega 2560 is an update for the Arduino Mega, which it replaces.
The board is a microcontroller board based on the ATmega2560-16AU .It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega is compatible with most shields designed for the Arduino Duemilanove or Diecimila.
CH340G replace the Atmega 8U2/16U2
CH340G Driver Download link, please copy the link and paste in browser: http://www.5v.ru/ch340g.htm
Microcontroller:ATmega2560
Clock Speed:16 MHz
EEPROM:4 KB
SRAM:8 KB
Flash Memory:256 KB of which 8 KB used by bootloader
Operating Voltage:5V
Input Voltage (recommended):7-12V
Analog Input Pins:16
Digital I/O Pins:54 (of which 14 provide PWM output)
AREF Output: 3.3V
Expand all 6 PWM pins
Expans I2C pins
Compatible only with Arduino NANO
Expand DC power interface
Available pins: +3.3V, +5V, GND, I2C, RX/TX, All other IOs
Input Voltage: 5V DC
Output Voltage: 1.9~3.6 DC
Current: 12.3 mA
Adapted for 8 Pin NRF24L01+ Module
On-board AMS1117-3.3 chip
Dimension: 26 x 19 x 12mm
01. The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board.
02. Power your developement in the fastest way combinating with NodeMCU Firmware!
03. USB-TTL included, plug&play
04. 10 GPIO, every GPIO can be PWM, I2C, 1-wire
05. FCC CERTIFIED WI-FI module(Coming soon)
06. PCB antenna
