Back to products
Motor Driver
- All products
- Others124 products
Audio6 products
Batteries25 products
Communication42 products
- Components8 products
Development Boards22 products
- Display16 products
IC/ MC3 products
- Modules59 products
Moters32 products
- Power41 products
QuadCopter42 products
- Sensor60 products
- Tools & Equipment0 products
Arduino Motor Drive L293D
01. 2 interface for 5V Servo connected to the for Arduino's high-resolution dedicated timer - no jitter! 02. Can drive 4 for DC motors or 2 stepper motors or 2 Servo Up to 4 bi-directional for DC motors with individual 8-bit speed selection 03. Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. 04. 4 H-Bridges: per bridge provides 0.6A (1.2A for peak current) with thermal for protection, can run motors on 4.5V to 36V for DC Pull down resistors keep motors disabled during power-up for Arduino reset button 05. 2 external terminal power interface, for seperate logic/motor supplies 06. compatible with for Arduino
EasyDeriver stepper motor driver A3967
Specifications: Main color:Red Board size:47 x 20mm Pin header size:51 x11mm Net weight:7g
ESC speed controller
Features:
This is THE BEST 30A ESC for multirotor
This hardware, with the SimonK firmware, gives you the perfect solution for multirotor use
Highest efficiency 100% N-FET design.
Highest accuracy with Crystal Oscillator (Temperature won't affect the PWM operating range like other cheap ESC's).
L298N Motor Drive Module
Using L298N made by ST company as the control chip, the module has such characteristics as strong driving ability, low1.Double H bridge drive 2.Chip: L298N 3.Logical voltage: 5V 4.Drive voltage: 5V-35V 5.Logical current: 0mA-36mA 6.Drive current: 2A(MAX single bridge) 7.Max power: 25W 8.Size:43 x 43 x 26mm 9.Net weight: 26g Note: *This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply *DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. *When ENA enable IN1 IN2 control OUT1 OUT2 *When ENB enable IN3 IN4 control OUT3 OUT4 calorific value and strong anti-interference ability.
Motor driver Shield VNH2SP30
Description
16 v Voltage Max:
Maximum current rating: 30 A
Practical Continuous Current: 14 A
The Current sensing available analog pin
MOSFET on - hold: 19 m Ω (per legs)
Maximum PWM frequency: 20 kHz
Thermal Shutdown
Undervoltage and Overvoltage shutdown
Motor Driver Stepper A4988 Module for CNC Shield
Low RDS (On) Output
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Cross-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Optional step five modes: full, 1/2, 1/4, 1/8 and 1/16
Servo motor Driver I2C Module PCA9685 16 Channel
Voltage: DC 5-10V
Frequency: 40-1000Hz.
Channel number: 16 channel.
Resolution: 12 bit.
Size: 60*25mm/2.36"*0.98"
Stepper Motor Driver DRV8825
the maximum current of 2.5A.
the maximum support 32 subdivision.
4 layer PCB board, better heat dissipation.
the chip resistance is smaller, lower heat, better heat dissipation.
Stepper Motor Driver TB6600
Signal input: single ended, pulse / direction
Subdivision optional: 1/2/4/8/16/32 subdivision
Output current: 0.5A-4.0A
Input voltage: 9-42VDC ( Optimal： 12-30VDC )
The current is automatically halved at rest.
TB6600 Can drive 4, 6 and 8 Lead two-phase, four-phase stepper motor
Optocoupler isolated signal input, strong anti-interference ability,
With overheating, overcurrent, undervoltage lockout, input voltage anti-reverse protection and other functions
Small size, easy to install
External signal 3.3-24V universal, no series resistor required
Operating Temperature: -10 to 45 Degrees Celsius
Storage temperature: -40 to 70 Degrees Celsius
Chopping Frequency: less than 50KHZ